Can I Install A Bath Tub Myself?
Can I Install A Bath Tub Myself?
Blog Article
What're your insights and beliefs on Tools You Need to Install a New Bathtub ?
Setting up a bathtub isn't precisely rocket science, yet it does require strong plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably challenging job. If the old tub is easily obtainable, the job can relocate rapidly; if you need to open a wall surface to remove the old tub and also position the brand-new bathtub, the job is much harder. In either situation, the task is within a house handyman's abilities, although you will require an assistant to leave the old bathtub and embeded in the brand-new one. Ensure you have actually qualified on your own for the work and fit trying it. Instead of working with a contractor to take over a halfway-completed task, it is better to take into consideration employing one before you start. Chances are you may require a specialist plumber to make tube connections.
This post will certainly help you set up a brand-new bathtub in your restroom if you have currently bought a new bathtub and also don't need to alter the setup of your previous water supply pipes.
Your tools as well as product list should make up the following:
Getting ready for the Setup
To start with, the sustaining frame supplied with the bath must be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be suited its last setting.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The procedure of removing the existing taps can be fairly troublesome because of the restricted accessibility that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the staying water that will originate from the pipelines. Once the supply pipelines have actually been removed, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before going on to fit the new faucets, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Making use of the two wood boards under its feet, put the bath tub in the needed setting. The wooden boards are practical in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the bath tub until the level reviews level.
To mount taps, fit all-time low of the furthest versatile faucet connector to the ideal supply pipeline by making a compression join; after that do the same for the various other faucet.
Switch on the water system and inspect all joints and also new pipework for leakages and also tighten them if required. Load the bathtub and additionally check the overflow outlet and also the normal outlet for leakages.
Finally, repair the bathroom paneling as described in the producer's user's manual. Tiling and also sealing around the tub needs to wait until the tub has actually been made use of at least once as this will certainly resolve it into its final setting.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap and the other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the installing hole in the bath/basin making sure that the washers remain in area in between the faucet and also the sink. Secure the tap in place with the producer supplied backnut. When the faucet is firmly in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind needs to be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a stiff seal, triggering the water to permeate the wall between the bath and the tiling, leading to complications with dampness and also feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your components and also installations. They are offered in tubes as well as cartridges, and are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched newspaper or soft rope. Remember to constantly load the tub with water before securing, to permit the motion experienced when the tub is in usage. The sealer can break fairly very early if you do not think about this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily available on the marketplace. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading up on Installing A Bathtub? Place a remark further down. We will be interested to hear your ideas about this content. Hoping that you visit us again in the near future. So long as you enjoyed our post if you please do not forget to pass it around. Thanks so much for taking the time to read it.
Schedule Here
Report this page